POLYBRON 707

DESIGNATION	POLYBRON 707 Supple liquid polyurethane watertightening system for concrete substrates Prepolymer reacting with air humidity. Semi-thick elastomer. Stable and UV resistant.
APPLICATION	Aliphatic polyurethane resin for outdoors applications. Outstanding colour stability outdoors.
LOCALIZATION	Protection of aromatic waterproofing coats indoors or outdoors Old or new concrete substrates, indoors and outdoors. Concrete and cement structures Wood and wood aggregates Ferrous and non ferrous metals Old coatings : make sure of the perfect adhesion of the previous protection and its compatibility with the primer. POLYBRON 707 suits to all waterproofing works or restoring.
SUBSTRATES	Top coat on POLYBRON 708 or direct on old or new concrete substrates, Concrete and cement structures, wood and wood aggregates Ferrous and non ferrous metals Old coatings : make sure of the perfect adhesion of the previous protection and its compatibility with the primer.
PROPERTIES	One-component polyurethane resin ready to use, in solution with an organic solvent allowing to obtain a waterproof coat. Supple and resistant polymerised film.
SUBSTRATE PREPARATION	The substrates have to be perfectly clean, dry and free from grease. Any impurity or non adhesive part should be removed. Cohesion should be checked. Sharp angles must be pressed down. Avoid humidity traces. Substrate humidity should not exceed 6%. Please refer to the technical data sheet of the adhesion primer adapted to the substrate.
APPLICATION	Manual application : Brush or roll without dilution. Apply two crossed and regular coats. Interval time between two coats : minimum 12 hours and maximum 48 hours. The application must comply with DTU norms and Art rules. Refer to the Cahier des Clauses Techniques VERITAS CEMEX-POLYBRON N°9 of 12/93 Do not apply if hygrometry is >85%. Do not apply by rainy or cloudy conditions. Minimum temperature for application : 5°C. The surface temperature must always be 3°C over the dew point temperature, according to temperature and humidity, determined by relative humidity. If temperature is >35°C, specific arrangements must be made.
EFFICIENCY	Average consumption : about 500 g/m² per layer. Average thickness with two layers is about 1mm. Drying @ 20°C and Relative Humidity 65% Dust free : 4 hours Overcoating : 12 hours Dry : 24 hours Full cure : 72 hours
PRECAUTIONS FOR USE	Flammable product, do not smoke Harmful product by inhalation Contains isocyanates. Use ventilated storage Keep away from food stuff Do not throw in sewerage system Reacts with water, alcohol and amines and produces gas release. Flash point > 26°C
TECHNICAL DATA	Aspect : Liquid solvented and viscous product Colour : Grey or cream Density : about 1.4 Viscosity 50000 @ 20°C Dry extract (weight) : 85% Ashes : 40% Shore hardness A : 65 Abrasion resistance : 100t/H18/1000g : 0.045 Tear resistance (DIN 53504) : 315% Tear resistance : (DIN 53504) : 8.9 N/mm²
SHELF LIFE	Shelter the closed packs in a dry, temperate and ventilated place. Avoid frost and temperatures > 30°C. Maximum shelf life : 6 months.
REGULATIONS	Road and Maritime Transport : RTMD Class 6.1 Art.723/Groupe 61310 Product irritating for eyes and skin. European labelling : R/20, R/36/37/38, R42 AFNOR Norms 30003 Famille 1 Class 6A

Information and recommendations contained in this data sheet are the result of experience gained under controlled circumstances and today knowledge. Their accuracy and completeness under the actual conditions of any intended use are not guaranteed and must be determined by our approved applicators since application is beyond control. Disclaims and any liability in excess of what is stated therein for results obtained, injury, direct or indirect damages. Total or partial reproducing of this document can only be made with our express agreement.